Build Guides · DIY Paver Patio
Build a Basic Patio: Step-by-Step with Material Quantities
A 10-by-12-foot paver patio needs 120 square feet of finished paving, a carefully compacted foundation, and a slight fall that carries rainwater away from the house. This guide works through the quantities, dimensions, and installation sequence for a straightforward rectangular patio using 12-by-12-inch concrete pavers.
Published November 10, 2026
The working plan: size, slope, and layers
A clean rectangle is a forgiving first layout, but its long, straight edges make accurate preparation essential. The example here measures 10 feet by 12 feet: multiply those dimensions to get 120 square feet. Order approximately 132 square feet of pavers, adding 10 percent for cuts, breakage, and the occasional piece that arrives chipped. If the patio will have several corners, curves, or a diagonal pattern, allow more for cutting.
The proposed paving assembly has three layers: a 6-inch compacted crushed-stone base, a 1-inch bedding-sand layer, and pavers approximately 2⅜ inches thick. That adds up to about 9⅜ inches from the finished surface to the prepared subgrade. The actual excavation depth depends on the paver thickness and the finished elevation you choose; measure the products you buy rather than relying on a catalog description alone.
Set the surface to fall away from the house. At a slope of ⅛ inch per foot, a 12-foot run drops 1½ inches. That is a practical target for this example, provided it directs runoff to a suitable area rather than a neighboring property, walkway, or foundation. Local drainage requirements and site conditions may call for a different solution.
Before marking the outline, check the height at the doorway. Keep the finished patio below the threshold and clear of siding, weep holes, and other openings. A patio that sits too high can trap water against the home, even when its surface is pitched in the right direction.
Materials for a 10-by-12-foot patio
These quantities are planning figures for 120 square feet. Site conditions, material grading, compaction, and product specifications affect final orders, so confirm quantities with your supplier before delivery.
- Concrete pavers: 132 square feet of 12-by-12-inch pavers, including a 10 percent allowance. A 12-inch square covers 1 square foot nominally, but check the manufacturer’s actual dimensions and joint recommendations.
- Crushed-stone base: about 2.25 cubic yards when measured at the finished compacted depth of 6 inches. Because the loose material settles during compaction and deliveries are not always exact, arrange roughly 2.5 cubic yards, then adjust for the supplier’s guidance.
- Bedding sand: about 0.37 cubic yard for a 1-inch layer; ordering approximately 0.5 cubic yard gives a modest working margin. Use sand specified for paver bedding, not play sand or a loose, rounded sand that shifts easily.
- Edge restraint: enough for the patio perimeter. A 10-by-12-foot rectangle has a 44-foot perimeter, so plan for at least 44 linear feet, plus any extra required by the restraint system’s joins and layout.
- Restraint spikes: the quantity and spacing depend on the product. Follow its instructions and buy enough for all sides, including joints and corners.
- Joint material: approximately 1–2 bags of compatible jointing sand may suit this example, but paver thickness, joint width, and bag coverage vary. Use the manufacturer’s coverage figure to calculate the actual amount.
- Optional separation fabric: geotextile fabric may be appropriate where the soil is soft or prone to mixing with the base. Ask a local aggregate or paving supplier whether it suits your soil and drainage conditions.
For a useful volume check, calculate base stone as area × depth: 120 square feet × 0.5 foot = 60 cubic feet. Divide by 27 cubic feet per cubic yard to get approximately 2.22 cubic yards at compacted depth. Bedding sand is 120 × 1/12 = 10 cubic feet, or about 0.37 cubic yard. Those figures describe the installed layers, not the loose volume delivered.
Tools and preparation
Gather a tape measure, stakes, mason’s line, string level or laser level, shovel, wheelbarrow, rake, hand tamper, plate compactor, screed rails, straight screed board, rubber mallet, and a level. A masonry saw fitted with the correct blade is useful for clean cuts, but it produces hazardous dust. Use appropriate eye, hearing, and respiratory protection, and follow the saw and blade instructions. For work that creates silica dust, use dust controls and protective measures suitable for the tool and conditions.
Call the local utility-location service before digging, even for a shallow patio. Marked services can change the excavation plan, and a hand-dug project still carries real risk around buried utilities. Check local rules for permits, setbacks, drainage, and any restrictions that apply to the property. If the ground is steep, unstable, or close to a retaining wall, get qualified advice before excavation.
Choose a dry-weather window if possible. Wet clay can smear and lose its structure underfoot, while rain can wash bedding sand out of an open excavation. Keep aggregates covered and separated from soil so the base does not become contaminated before installation.
Step 1: Mark the footprint and set the finished height
Mark a 10-by-12-foot rectangle with stakes and mason’s line. Measure both diagonals: for a true rectangle, each should be about 15 feet 7⅝ inches. If the diagonal measurements differ, shift a stake until they match. This check catches a layout that looks square from one corner but gradually drifts out of line.
Decide which 12-foot direction will carry the drainage fall, then set the lines to show the finished surface height at both ends. A 1½-inch drop over 12 feet gives the example’s ⅛-inch-per-foot slope. Use a level, string line, or laser to check the grade rather than judging it by eye. Keep the finished height below the doorway and away from vulnerable siding or openings.
Measure from the finished surface down through the paver, bedding sand, and compacted base to establish the excavation level. With 2⅜-inch pavers, a 1-inch bedding layer, and a 6-inch compacted base, the nominal build-up is 9⅜ inches. Add a small allowance for final adjustment only if your layout and site elevations support it; do not excavate blindly to a single depth if the ground itself slopes.
Step 2: Excavate without losing the grade
Remove sod and topsoil across the patio footprint, extending the work area enough to accommodate the edge restraint and compactor. Topsoil and roots are not stable support for pavers. Excavate to the planned subgrade, keeping the bottom consistent with the intended fall away from the house.
Check depth from the finished-height lines at several points, especially corners and the center. A shallow hollow may remain hidden beneath the base until the pavers settle; a high spot can leave too little stone where you need support. Correct the subgrade now by cutting high areas or filling and compacting low areas with suitable base material. Do not use loose topsoil to make up a low patch.
Look at how water behaves on the exposed soil. If water collects or the soil pumps underfoot, pause rather than burying the problem under aggregate. The design may need improved drainage, a different base detail, or professional assessment. Keep the excavation clear of loose debris and avoid tracking mud into it.
Step 3: Install and compact the stone base
Spread crushed stone in lifts instead of placing the full 6 inches at once. For many small-plate compactors, lifts of about 2 to 3 inches are manageable; use the equipment instructions and the aggregate supplier’s recommendations. Rake each lift to an even depth, lightly shape the intended slope, and compact it before adding the next. A loose 6-inch layer can finish well below 6 inches after compaction.
Make multiple, overlapping passes with the plate compactor. Avoid skipping the edges, where the base is often least firm. After each lift, check the surface for soft spots and confirm that the grade still falls away from the house. Add material where necessary and compact again, rather than trying to correct an uneven foundation with bedding sand.
The finished stone layer should be firm, even, and approximately 6 inches deep after compaction. A hand tamper can help in restricted corners, but it is slow and may not compact a large area as uniformly as a plate compactor. If you hire equipment, ask how to operate it safely and confirm whether the rental includes a protective mat suitable for use near sensitive surfaces.
Step 4: Screed the bedding sand
Set two screed rails on the compacted base and adjust them to create a level plane that follows the planned slope. Spread bedding sand between the rails, then pull a straight board across them to establish a smooth, consistent 1-inch layer. Work in manageable sections so you do not have to step on finished sand.
Do not compact the sand before placing the pavers, and do not use it to disguise dips in the stone base. Thick or uneven bedding layers can settle inconsistently. If a section is too low or high, lift the rails, correct the base, and screed again. Remove the rails carefully and fill the grooves with sand, smoothing the surface without disturbing the surrounding bed.
Only screed as much area as you can cover with pavers before weather or foot traffic affects it. Keep tools and materials off the finished bed; even a heel can leave a depression that later appears as an uneven paver.
Step 5: Lay pavers from a straight reference edge
Begin along the straightest, most visible edge, using a rigid reference such as the house-side layout line or a properly positioned edge restraint. Work forward across the sand bed, laying pavers without twisting them into place. Keep joints consistent with the manufacturer’s recommended spacing; concrete pavers are not always exactly 12 inches across, even when sold as 12-inch squares.
Check alignment every few rows with a string line. Use a rubber mallet for small adjustments, and check for rocking as you go. If a paver sits low or high, lift it, correct the bedding beneath it, and reset it. Do not strike pavers with a steel hammer, and do not force a misaligned row into place until you know where the error began.
At the perimeter, measure each opening and mark the cut with a square. Use a wet-cutting method or the dust-control system specified for your saw and blade. Wear eye and hearing protection and keep bystanders away from the cutting area. Dry-cutting concrete can generate respirable silica dust; do not treat a basic dust mask as a substitute for appropriate controls.
Step 6: Secure the edge and fill the joints
Install edge restraint around the exposed perimeter, following the product’s instructions for placement and spike spacing. For this rectangle, the perimeter is 44 feet. Secure the restraint into the compacted base, not into loose soil, and make sure it sits snugly against the outer pavers. A strong edge keeps the paving field from gradually spreading under foot traffic and seasonal movement.
Sweep compatible jointing sand across the surface until the joints are filled. Use the material specified for your pavers; some joint products have particular requirements for moisture, joint width, or installation conditions. Run the plate compactor over the paving only when the paver manufacturer and equipment guidance allow it, using a protective mat where appropriate. Refill joints after compaction because sand can settle into gaps.
Brush away excess sand before wetting or applying any product. Follow the joint-material instructions for final setting and curing. Avoid sealing a new patio immediately unless the paver and sealer manufacturers specifically recommend it; sealing is a separate surface-care decision, not a substitute for a stable base or full joints.
Step 7: Inspect drainage and the finished surface
Check the finished height at the doorway and along the foundation. Confirm that the surface still drops away from the house: across the 12-foot run in this example, the target fall is about 1½ inches. Use a straightedge and level to identify local dips that could hold puddles, and re-seat affected pavers before the work is considered complete.
Inspect the perimeter for open joints, loose restraint, and cuts that leave narrow or unsupported pieces. Look at the patio after a light rain if possible. Water should move toward the intended drainage area rather than collecting beside the house or spilling toward an unwanted location. If the site directs water toward a foundation or adjacent property, stop and resolve the drainage plan instead of accepting the result.
Expect to top up joint sand after the first few rains if it settles. Keep spare pavers from the same batch in a dry place; a few replacements are useful if a piece is damaged or the patio needs a future repair.
Common mistakes that cost time later
- Ordering exactly 120 square feet: the finished area is 120 square feet, but cuts and breakage make 132 square feet a more practical starting order for a simple rectangle.
- Measuring base depth before compaction: 6 inches of loose stone will not necessarily become 6 inches when compacted. Build and check the base in lifts.
- Using sand to fix a poor base: bedding sand is a thin, even setting layer. Correct base dips before screeding it.
- Ignoring doorway height: the planned layer thickness must fit below the threshold without covering siding, weep holes, or other openings.
- Leaving out edge restraint: unconfined pavers can move outward, opening joints and disturbing the pattern.
- Assuming water will find its own way: establish a drainage direction in the layout and verify it after the pavers are installed.
A final materials and quality check
Before work begins, confirm the paver’s measured thickness, the supplier’s aggregate coverage and compaction guidance, and the sand’s suitability for bedding. Recalculate excavation depth if the pavers differ from the 2⅜-inch example. Keep the key dimensions together: 10 by 12 feet, 120 square feet of finished surface, approximately 132 square feet of pavers, a 6-inch compacted stone base, a 1-inch bedding layer, and a ⅛-inch-per-foot fall away from the house.
After installation, check the corners and diagonals, confirm the edge restraint is secured, and make sure the joints are filled. A patio that looks polished on day one depends on what cannot be seen: an even subgrade, compacted base lifts, controlled bedding depth, and drainage that works with the property rather than against it. Take time over those details, and the simple rectangle becomes a durable outdoor room built to suit the home.